Engraving Blanks
Recommended Cutting Parameters
| Material Types | RPM | IPM | RPM | IPM | RPM | IPM | RPM | IPM |
| Non-Ferrous Materials | ||||||||
| Aluminum /Aluminum Alloys | 3000 | 4.5 | 6000 | 9 | 7500 | 12 | 10000 | 15 |
| Brass / Bronze | 3000 | 4.5 | 6000 | 9 | 7500 | 12 | 10000 | 15 |
| Copper / Copper Alloys | 3000 | 4.5 | 6000 | 9 | 7500 | 12 | 10000 | 15 |
| Magnesium /Magnesium Alloys | 3000 | 4.5 | 6000 | 9 | 7500 | 12 | 10000 | 15 |
| Glass Filled / Phenolics / Plastics | 3000 | 4.5 | 6000 | 9 | 7500 | 12 | 10000 | 15 |
| Cast Irons | ||||||||
| Cast Irons / Soft | 3000 | 4.5 | 6000 | 9 | 7500 | 12 | 10000 | 15 |
| Cast Irons / Hard | 3000 | 2.4 | 6000 | 4.8 | 7500 | 6 | 10000 | 8 |
| Ductile Iron | 3000 | 3 | 6000 | 6 | 7500 | 7.5 | 10000 | 10 |
| Malleable Iron | 3000 | 3 | 6000 | 6 | 7500 | 7.5 | 10000 | 10 |
| Steels | ||||||||
| Low Carbon Steel | 3000 | 3 | 6000 | 6 | 7500 | 7.5 | 10000 | 10 |
| Medium Carbon Steel | 3000 | 4.5 | 6000 | 9 | 7500 | 11.3 | 10000 | 15 |
| Hardened Steel | 3000 | 1.5 | 6000 | 3 | 7500 | 3.8 | 10000 | 5 |
| Stainless Steels | ||||||||
| Stainless Steel / Soft | 3000 | 3 | 6000 | 6 | 7500 | 7.5 | 10000 | 10 |
| Stainless Steel / Hard | 3000 | 1.5 | 6000 | 3 | 7500 | 3.8 | 10000 | 5 |
| High Temperature Alloys | ||||||||
| Monel | 3000 | 3 | 6000 | 6 | 7500 | 7.5 | 10000 | 10 |
| High Nickel Steel | 3000 | 1.5 | 6000 | 3 | 7500 | 3.8 | 10000 | 5 |
| Nickel Base High Temperature Alloys | 3000 | 1.5 | 6000 | 3 | 7500 | 3.8 | 10000 | 5 |
| Hardened Materials | ||||||||
| Titanium / Soft | 3000 | 3 | 6000 | 6 | 7500 | 7.5 | 10000 | 10 |
| Titanium / Hard | 3000 | 1.5 | 6000 | 3 | 7500 | 3.8 | 10000 | 5 |